Tel: +386 1 56 44 770
iii.PRODUCTS
 

 

 

 


 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

oKOCH, servisna oprema, d.o.o.
oŠpruha 42
oSI-1236 Trzin
oSlovenia
oTel: +386 1 56 44 770
oFax: +386 1 56 44 772
oGsm: +386 41 638 609
oaleksander.presekar@koch.si

o

Roller brake tester for passenger cars Beissbarth BD 600/660

Roller brake tester for passenger cars Beissbarth BD 600/660
Model BD 600: width 800-2200 mm

Model BD 660: width 800-2800 mm


Characteristic:
• Entrance brake tester with BNET fieldbus, .
.
easy upgrade with options for superautomtic
.
mode (LCD/PCStation) and reverse turning
. mode for 4x4vehicles
• No bulky control cabinet because all testdevices . have electronic onboard
• Galvanised testdevices meet highest quality
.
requirements
• Fully automatic test procedure, operation by
.
start/stopkey or infrared remote control
• Universal analog display with redyellowgreen
.
evaluation scale based on vehicle category
.
selection
• Outdoor installation possible
• Individual installation planning because of
.
flexible cable length (30m BNET fieldbus
.
cable in the delivery set)

Tehnical data:
Basic Data:

Dimensions: W x L x D (mm) 2360 x 660 x 250
Weight approx.: 420 kg
Friction value dry: 0.8
Friction value wet: 0.7
Roller length: 700 mm
Roller diameter: 205 mm
Largest test width: 2200 mm
Smallest test width: 800 mm
Elevation of rear rollers to front rollers: 25 mm
Height difference roller upper edge front to shop

.
floor: – 10 mm
Smallest testable wheel diameter:
. ~ 320 mm (10’’)
Largest testable wheel diameter:
. ~ 800 mm (20’’)
Permissible test axle load: 3500 kg
Permissible max. driveover load: 4000 kg
Maximum braking force per wheel: 7.5 kN
Noise emission: LwA <75 dB (A

Roller Surface:
Expanded metal DIN 791 (rib mesh)
. mesh length: 62 mm
Mesh width: 21 mm
Bar thickness: 2 mm
Bar width: 2.5 mm
Rib mesh thickness: 2 mm
Plastic corundum coating of interstices
. with plastic
Plastic coating approx:. 1 mm over rib mesh
Grain size: 2.0 to 3.2 mm
Roller colour black

Performance Data:
Voltage supply: 3 x 400VAC / 9.8A / 50/60 Hz
Fuse supplied: 3 x 20Z / C 3pin (400V)
Feed line supplied: 5 x 2.5 mm? (400V)
Test speed: 2.6 km/h
Nominal output of the drive motors: 2 x 3.7 kW

Optional 230V:
Voltage supply: 3 x 230VAC / 17A / 50/60 Hz
Fuse supplied: 3 x 25A / C 3pin
Feed line supplied: 4 x 2.5 mm

Environmental Conditions:
Protection class:
. (according to DIN 40 050) IP 54
Permissible humidity (relative without
.
condensation): up to 85%
Operating temperature: 10 to +60 °C
• Storage 10 to +60 °C

<< back to previous page................................................................................. next page>>
<< back to page Brake testers and test lines


1